Видео

Hi I need to lean this type of welding

Yes learn to stick weld first..because it will permanently drill into your head what a dirty, always potentially dangerous process welding is. Those fizzling sticks, coated with ( lets face it) God knows what, smoking stinking and flashing over onto everything around you, while the barely controllable arc dumps HUGE amounts of heat into the work piece. Start with stick welding because you might as well get it over

Great content! Thank you

Hi sir can i ask a question did you try mig weld smootharc 250c advance with inductance?

Well done for stating your work in mm mate. Nice job too. Namaste x

I'll keep watching your videos. Your vocabulary usage is easy fer a dummy like myself to understand welding. Nuffced

From India ❤

I’m into the building side of this channel. Keep it up :)

I am hearing that the brand of flux core wire makes a big difference on how much slag will be lifting off compared to chipping it off with the hammer. Which brand of flux core do you recommend for almost hassle free welding?

thats what i use for weldig 16 gage steel sheet

Very Nice congratulations

What is the best way to measure and cut a 45 angle on square tubing?

Good video but honestly, unless you’re really limited on amperage an experienced welder can use either just a matter of dialing the machine in

Is there a nitrile coating on the top

This is funny and awesome. Next V8 blender for V8 smoothies

Thank you tim best explanation ive seen yet can youbdo one on pulse spray also

Dude you just gave the best explanation I've heard when you say your heating to creat a pool and then adding to it. Well said🎉

welding pipe is hard to me not only it looks like shit it has pin holes all though it

Great bit of kit, and it’ll never rot being that thick.👌😎🏆

The lesson learned here is to clean off the oxide layer first for better results

Hello, I have two questions. I purchased a cheap arc welder on Amazon, for like $70.. the picture shows the grounding clamp going into the positive terminal. It came with J422 sticks.. I used the negative side and was able to get an arc but wondering if maybe it was a mistake in the picture or if I should be using the positive side.. Also, I'm trying to customize the size of some powder coated fencing panels I got from menards to put on my retaining wall.. just the cheaper vertical 36" by 48" panels. What is the best electroid to use for this type of material? Should I be completely removing the powder coating at the weld site? If so how wide? I was having A lot of trouble using the J422.. melted a hole. And had trouble maintaining an arc. Thank you.

wow, I actually understood what you were talking about! Great video thank you.........ALMOST feeling the need to learn, my biggest concern is being able to hold the torch consistently close enough to form a good weld.....

Amazing! good job looks great!

Now weld that vice and try again! Good video. Thanks.

Only a few spools of wire? Christ I'm going to go broke.

Lowest amp and tiniest rode is ideal masters says

There are some of these little inverter DC stick welders with a "lift TIG" setting, although I have yet to try one.

6013 is basically sheet metal rod because it does not penetrate. Try 6010 dc rod or 6011 ac rod all around most versatile mild steel rods that penetrate you will never go back. No reason to fight with a welding rod that doesn’t penetrate and traps slag.

How much did this cost overall and what is the top speed?

7018 3/32 what causes the slag to look wet?

You have that backward, voltage is not what is dangerous, it is amperage that matters. Hence why a Tesla coil is safe. It’s high voltage, low amperage.

Excellent inf! Thanks! Fixing my tractor.. no stick experience really.. mostly mig... subscribed!

What is the difference between these an the Evolution orange one?

thanks a lot

thanks a lot

thanks a lot

thanks a lot

I can't seem to weld 16-14 gauge metal without burning through even on the lowest settings ( Letter and number dials) . I'm using the 035 wire the machine came with. Will switching to 030 wire help?

This was a wonderful video with great arc shots! I learned a ton thank you!

Thank you for the nice video. I'm thinking of buying your course but I'm a bit lazy, is everything metric-compatible in the course or, do I have to use my brain? (e.g. Amps/thou is not a useful unit on my bank of the pond) I suggest you copy your answer in the course blurb too :)

Damn you, all I wanted to know was how to repair my bandsaw blades and now I want to get a welding machine. I have hobbies enough as it is.

I have used almost all CAD software you mentionned, except free version of Solidedge. Talking about Fusion360, as you mentioned that drawing export is limited. In fact, it is not limited. Unfortunately, it's more than limited. You cannot export a drawing you created in Fusion360. The only option you have is Screenshot.

My favourite electrode is 6013 because its all purpose and very flexible .i have experienced with 7018 but 6013 its something else

Hi

Problem is that people use pulse on everything its really only beneficial for outta position or if heat input is a issue axil spray gets better penetration than pulse

Great tool. Useless outcome.

What’s a good machine with this capability? And economical

Great tutorial

Is it true that if I change the stick from negative to positive I'll get a different kind of weld?

THANK YOU for this video... This is the one question I've just spent hours trying to find the answer. Which one to start with, and here you are.